Table saw and mitre saw safety: riving knives, guards and push sticks
Checked 19 November 2026
What HSE’s woodworking guidance says about riving knives, top guards, push sticks and keeping hands clear on circular and cross-cut saws, and which of those safety features the makers list on the saws in this guide.
Table saws and mitre saws are where many home workshops start, and they share the same two hazards: touching the blade, and the workpiece being thrown back at you. HSE’s woodworking pages give precise figures for circular saw benches and cross-cut saws in workplaces. Home and site saws are smaller, but the guidance explains what each guard is for — and the makers’ feature lists show which of those guards your saw has.
This is general information, not training. Where your saw’s manual says something different, follow the manual.
Table saws: the riving knife
The riving knife is the curved steel plate behind the blade. HSE explains that it stops the wood closing onto the blade and being thrown back. HSE’s rules for saw benches:
- fit it and set it within 8 mm of the blade;
- it must be thicker than the saw blade’s body but thinner than the cut (kerf);
- a different blade may need a different riving knife.
That last point matters if you change blades: check that the new blade suits the knife on your saw. DeWalt’s DWE7485 compact table saw has a non-through-cut riving knife, anti-kickback pawls and a blade guard, and stores them on board so they don’t go missing.
The top guard
HSE says the top guard should be adjusted to cover the gullets of the blade’s teeth, to stop splinters being thrown out. The DeWalt is supplied with an upper guard assembly; check your own saw’s manual for how its guard is set and when it may be removed.
Push sticks
HSE’s figures for saw benches are specific:
- a push stick at least 450 mm long, made from sound material with a “bird’s mouth” notch cut into the end;
- always use it for the last 300 mm of a cut.
Makers agree that a push stick is essential. Einhell says one is required for safety on its TC-TS 200 and gives it a holder on the saw; DeWalt includes one with the DWE7485. Makita lists a push stick as an accessory for the MLT100N, so check what comes in the box with the version you buy. Search Amazon for table saw push sticks.
Fence, blade height and support
- Fence: HSE says the fence shouldn’t overlap the blade by more than 18 mm, to reduce the risk of the work being thrown back.
- Blade height: HSE says to set the blade so the top teeth pass completely through the wood.
- Support: on a workshop saw bench HSE wants at least 1,200 mm from the blade spindle to the back of the table, so you can take the work off without reaching near the blade. On a small bench-top saw, plan how you will support long boards before you start.
Choose a saw that suits the work
A small saw pushed beyond its job is a hazard in itself. Einhell sells the TC-TS 200 (200 mm blade, 800 W) for DIY and home workshop use. The DeWalt DWE7485 (210 mm, 1,850 W) rips up to 622 mm to the right of the blade. The Makita MLT100N (260 mm, 1,500 W) cuts 93 mm deep at 90° and lists an electric brake and soft start. See machinery safety at home and at work for the “suitable for the job” test.
Mitre saws: what HSE says about cross-cut saws
A mitre saw is a cross-cut saw: the blade comes down or across to the wood. HSE’s cross-cut saw guidance says:
- guards must cover as much of the blade as possible;
- cross-cut saws should have a brake, or a device that returns the cutting head so the blade sits in a protected area;
- keep a “no-go” area for hands of 300 mm either side of the blade, so the blade can’t be pulled over a thumb or fingers;
- a hold-down can be used for small pieces.
The makers’ lists show how the saws in this guide handle this. Makita lists an electric brake, soft start and a laser for its LS1019L, with vice assemblies to hold the work. DeWalt supplies a material clamp with the DWS780. Einhell lists a clamping device, soft start and adjustable workpiece supports for its cordless TE-SM 36/10 L Li-Solo. Use the clamp rather than holding short pieces by hand near the blade.
Noise and dust
Saws are loud. Makita gives a sound pressure of 91 dB(A) for the LS1019L and 89 dB(A) for the MLT100N, above the 85 dB(A) level at which employers must provide hearing protection — see noise and hearing protection. They also make fine dust: connect extraction (Einhell, for example, supplies an adapter for a 36 mm vacuum hose on the TC-TS 200) and read wood dust and dust extraction.
Before every cut
- Riving knife and guard fitted and set as the manual says.
- Push stick within reach for table saw cuts; clamp ready for the mitre saw.
- Hands outside the 300 mm zone either side of a mitre saw blade.
- Long work supported before you start.
- Eye and hearing protection on, extraction running.
- Unplug the saw before changing the blade or clearing offcuts.
As an Amazon Associate we earn from qualifying purchases.
General information only. Always read and follow the maker’s manual and safety instructions, wear the protection it tells you to, and keep children and pets away from machinery. This guide summarises official and makers’ guidance; it isn’t legal or professional advice.
Sources
- HSE: Circular saw bench (rip saw) (updated 18 October 2024) (checked 19 November 2026)
- HSE: Cross-cut saw (updated 18 October 2024) (checked 19 November 2026)
- DeWalt UK: DWE7485 210mm compact table saw (checked 19 November 2026)
- Makita UK: MLT100N table saw (checked 19 November 2026)
- Einhell: TC-TS 200 table saw (checked 19 November 2026)
- Makita UK: LS1019L slide compound mitre saw (checked 19 November 2026)
- DeWalt UK: DWS780 305mm mitre saw (checked 19 November 2026)
- Einhell: TE-SM 36/10 L Li-Solo cordless mitre saw (checked 19 November 2026)
- HSE: Noise at work regulations (checked 19 November 2026)
Checked 19 November 2026.